Flash point testers Manufacturers | Flash point testers Suppliers - F.I.CL

Hot Wire Coil Ignition Tester

Hot wire coil ignition tester measures the specimen’s ignition time during hot coil is heated electrically. After heating the specimen that flows electricity by rolling it with hot coil which produces 0.25 ~ 0.27W/? linear power density to 120 seconds, this equipment records the time it is...

Read More Inquiry Now
Explosion Limitation Tester

This test method covers the determination of the lower and upper concentration limits of flammability of chemicals having sufficient vapor pressure to form flammable mixtures in air at atmospheric pressure at the test temperature. This test method may be used to determine these limits in the presence of inert dilution gases. No oxidant stronger than air should be...

Read More Inquiry Now
Offshore HCF Cable Fire Resistance Tester

HCF-NEK606 is an equipment that can decide whether power lines or control lines used in the coast, ships and refineries are resistant to high heat that may be caused by oil or...

Read More Inquiry Now
Solar Cell Spread of Flame & Burning Brand Tester

This equipment virtually simulates an external fire to evaluate the resistance of the roof and other physical elements of fire, in order to qualify for the flame spread experiments (A~C class), in case of A 1.82m, B 2.4m and C 3.9m. It is equipment to displacement of the testing material and the exposure and falling of the roof...

Read More Inquiry Now
Radiant Panel Flame Spread Tester

The Radiant Panel Flame Spread Tester is an equipment using gas ignited Radiant heat panel to test the surface combustibility of Building product (ASTM E 162) and cellular plastics (ASTM E 3675), Radiant Panel Index (Is) is measured by the flame radio-waves, Critical Heat Flux,(CHF) and Heat Release...

Read More Inquiry Now
Vertical Furnace Heat Flux Tester

It is a heat (radiant heat) flux tester of limited window or fire-retardant door to prevent spread of fire and to secure exit path near the window or fire-retardant door. This tester is used to allow heat radiation test for supplementing fire protection test of windows in Grade A, Grade B, and Grade F compartment for ships specified in FTP Code I / Annex 1/Vol. 3/ Appendix 1. It refers to heat flux testers through windows to prevent spread of fire and secure exit path near the window as window is featured by limitation of heat...

Read More Inquiry Now
Building Construction Fire Resistance Tester

FESTEC’s Building Construction Fire Resistance Tester measures the performance of construction material against standard fire conditions, and satisfies the general requirements, vertical history section material, vertical non-history section material and the fire-proof door’s fire proof testing.@ This equipment tests about the walls, doors, dampers, connections, through type sealing material, etc. such as the product of test for fire...

Read More Inquiry Now
Fire Resistance Assemblies Tester

FESTEC’s Fire Resistance Assemblies Tester is included in both the IEEE 1202 and IEEE 383 standards. This test method is proceed in a chamber with a set volume for 20 minutes. During the 20 minutes, a sample cable is ignited with theoretically 20kW(70,000Btu/hr) flame using an ignition source fixed in a vertical position. This equipment evaluates a spread of flame of single core cable or multi core cable. If user wants to measure H.R.R (Heat Release Rate), Smoke density and so on, Heat Release Facility (additional part) is adoptable to this...

Read More Inquiry Now
ISO 5659 Assembly Tester

FESTEC’s ISO 5659 is to measure and observe shape of test specimen by radiation heat of Conical Heater, and measures ignition time and mass loss rate. FESTEC’s ISO 5659 Assembly Tester is an optimal equipment for measuring and observing ignition time and mass loss rate of test specimen as well as shape of test specimen by radiation heat in the chamber with a given volume(914?×610?×914?). In this tester, static smoke is generated in the chamber as the level test specimen with the surface receives radiation heat (10~70 kW/m2). FESTEC’s ISO 5659 Assembly Tester fully complies with...

Read More Inquiry Now
Thermal Radiation Resistance Tester

Thermal Radiation Resistance Tester of full face mask measures exposure radiation from radiation heat resource and evaluates leakage of mask and either valve works or...

Read More Inquiry Now
Full Face Masks Flame Resistance Tester

Full Face Masks Flame Resistance Tester is test when full face mask’s class 2,3 (follow up KIF’s standard) is exposed on the flame, check for either burn on the parts of full face mask or keep burn over 5 second after without...

Read More Inquiry Now
Flooring Radiant Panel Tester

This surface of the material spread flame tester (ISO 9239, Flooring Radiant Panel Tester) is test method that formal reflected spread of flame on flooring material back-draft condition when fire on building happened flame at compartment or room adjacent, or high temperature gas radiated to flooring surface a hot radiation heat accumulated at upper of midway during a fire at an early growing step. More detail as see the next view; specimen is located at down horizon of 30 degree sloped gas radiation panel per horizon surface. Pilot flame as ignition resource put a part edge of specimen on...

Read More Inquiry Now
45 Degree Flammability Tester

45 Degree is used to evaluate compliance of fire-retardant products with fireretardant performance standards according to the combustion method, and measures combustion characteristics such as After Glow and After Flame of test specimen installed at a 45-degree angle. FESTEC 45°Flammability tests After Flame Time and After Glow Time of specimen by heat in the chamber. This measures flame retardance about specimen of less than 5mm thick (Board, Plate, Sheet, Film and so on) by 45°Micro and Airmix method and evaluates materials about 3rd grade of flame retardance (less than 15cm and 5...

Read More Inquiry Now
Spread of Flame Tester

IMO is used to evaluate combustion characteristics of building materials and ship materials and measures spread rate of flame, flame for ignition by distances, CFE (Critical Flux at Extinguishment) and total heat release. This test method is originated from ISO 5658-2 (Reaction to fire tests–Spread of flame- Part 2 Lateral spread on building products in vertical configuration) and measures combustion characteristics of vertical specimen (155mmX800mm). The specimen is exposed to the reasonable radiant heat field and is measured by thermocouple for exhaust gas calibrated through the progress...

Read More Inquiry Now
Erosion Tracking Tester

Erosion Tracking Tester measures the resistance to tracking and erosion by using liquid pollutants and inclined plane specimens. This tester can be evaluated resistance to tracking and erosion of electrical insulation materials used under severe ambient conditions and has two kinds type test way which are constant tracking voltage and stepwise tracking voltage is...

Read More Inquiry Now
Water Spray Tester

FESTEC’s BS 6387 Tester, BS 6386 standard is belong to British, is a testing device that checks for the standard level of current in the cable, and also checks the cable’s resistance for heat and water of the...

Read More Inquiry Now
Fire Mechanical Shock Tester

FESTEC’s IEC 60331-12 tester is used in test conditions where the basic flame temperature is at least 830? and tests the cable exposed to flame and mechanical shock that needs to maintain the circuit...

Read More Inquiry Now
Fire Resistance Tester

FESTEC’s IEC 60331-11 tester is used in test conditions where the basic flame temperature is at least 750? and tests the cable exposed to the flame that needs to maintain the circuit...

Read More Inquiry Now
IEC60754-1&2

FESTEC’s IEC 60754-1&2 Tester measures gas volume of Halogen Acid (IEC 60754-1), pH concentration(PH Meter, Hydrogen ions, IEC 60754-2), Conductivity(IEC 60754-2) and etc from a wire (cable) by radiant heat in the Tube Furnace (IEC 60754-1: 800°c, IEC 60754-2: 950°c) Especially, FESTEC’s IEC 60754-1&2 is enable to test both IEC 60754-1 and IEC 60754-2 standards by one equipment and mode select function. IEC 60754-1 is halogen-free cable came from and including the polymer to halogenated compounds on the basis of the additive compounds emitted during combustion, except the...

Read More Inquiry Now
Single Vertical Flame Spread Tester

FESTEC’s Single Vertical Flame Spread Tester is included in IEC 60332-1, IEC 60695-2-4-0 & 1 standards. This test use for method requires a set volume Chamber in standardized for source of ignition in electrical or optical, make stand straight of wires or cables vertically for the vertical arrange flame spread of the...

Read More Inquiry Now

We are aimed to help Companies from South Korea to expand their Market Globally. We do Market Research, Buyers Data Sources, Global Marketing, Exebitions and Trade Shows, Global Trade Distribution, Infrastructure & Finding Global Partners on behalf of companies. We help korean companies to sell Made In Korea products from our stores. Get sign up to receive more updates from Best Made In Korea.

© 2022 Bestmadeinkorea. All Rights Reserved.