BIT TYPE - PRESSURE TANK  • Casting type tank that comes economical with low price.

BV-322PThere is no remaining pressure and very good for cutting off the liquid with using precision nozzle. (Precision nozzle type) <SPECIFICATIONS> Operating type Needle Off Maximum dose 8l / Min Viscosity range 1~100,000cps Operating air pressure 4kgf/cm² Maximum fluid charge

BAT TYPE - PRESSURE TANK• Used to stir the liquid in case of any precipitation, vacuum extraction, heating ups. Capacity H1 H2 OD ID D P.C.D Sanitary Bolt Hole Size Internal container BAT-1L 306 336 114 108 174 154 4.5" M10-4EA 3-120°Ø7 OptionMaterial : SUS,PE,Teflon,Teflon

BV-302Needle off type. Offer highly precise dispensing. You can simply adjust deposit volume minutely. <SPECIFICATIONS> Operating type Needle Off Maximum dose 8l/Min Viscosity range 1~100,000cps Operating air pressure 4kgf/cm² Maximum fluid charge pressure 6kgf/cm² Maximum number of

BV-350 Ultra high pressure valve to be used for liquid of very high viscosity. <SPECIFICATIONS> Operating type Needle Off Maximum dose 28l / Min Viscosity range 1~Paste Operating air pressure 4kgf/cm² Maximum fluid charge pressure 300kgf/cm² Maximum number of cycles 150

BV-303  Suck- off type. Most suitable for the process requiring the vacuum efficiency to prevent the remaining pressure after dispensing. Operating type     Suck-Back Maximum dose 8l/Min Viscosity range     1~200,000cps Operating air

BV-300N Diaphragm and Needle Type. The device of which the part to contact liquids is made of UPE and it’s suitable for Anaerobic and liquids requiring the chemical resistance. Operating type     Diaphragm Maximum dose 0.3l/Min Viscosity range     1~5,000cps Operating air pressure

BV-300T Diaphragm and Needle Type. The device of which the part to contact liquids is made of UPE and it’s suitable for Anaerobic and liquids requiring the chemical resistance Operating type         Diaphragm Maximum dose 0.3l/Min Viscosity range

BV-520M  Mostly attached to FA line, and used with general hub needles or metal needles. The position settle faculty is very excellent, so easily use it with no extra position control even after replacing needle. (Needle type) Operating type Needle Off Maximum dose 0.8l/Min Viscosity

BV-500  Spray Valve type. The valve only for spray. It controls spraying up to 7mm width at minimum. <SPECIFICATIONS> Operating type Needle Off Maximum dose 8l/Min Viscosity range 1~1,000cps Operating air pressure 5kgf/cm² Maximum fluid charge pressure 10kgf/cm² Maximum number of

BV-386  High pressure valve of high discharge accuracy, capable to easily fine tune the discharge flow. <SPECIFICATIONS> Operating type Needle Off Maximum dose 28l / Min Viscosity range 1~Paste Operating air pressure 5kgf/cm² Maximum fluid charge pressure 150kgf/cm² Maximum number of

BV-305  Suck back type. The big orifice is fit for dispensation of large capacity works. Operating type Suck-Back Maximum dose 28l/Min Viscosity range 1~200,000cps Operating air pressure 5kgf/cm² Maximum fluid charge pressure 50kgf/cm² Maximum number of cycles 150times/Min Air

  BST TYPE - PRESSURE TANK • Interior and upper size of the tank are identical which enables use of interior case. • Generally used for under 20 liter container     Capacity H1 H2 OD ID D P.C.D Bolt Hole Size Internal

BMT TYPE - PRESSURE TANK  • Hinge clamp type tank. Used by directly inserting the interior container • Suitable for large quantity and high pressured material. Capacity H1 H2 OD ID D P.C.D Bolt Hole Size Internal

BV-520P  Mostly attached to FA line, and used with precision nozzle. The position settle faculty is very excellent, so easily use it with no extra position control even after replacing nozzle. (Precision nozzle type) Operating type Needle Off Maximum dose 0.8l / Min Visicosity range 1~50,000cps

  BFT type• It is easy to open and close the tank(clamp). With the inner and outer sides abraded, it is excellent in cleanness and endurance. • It is suitable for using when transporting low viscosity liquid by pneumatic pressure. Capacity H1 H2 OD ID D P.C.D Hole

BV-389  High pressure valve of high discharge accuracy, capable to easily fine tune the discharge flow. <   SPECIFICATIONS> Operating type Needle Off Maximum dose 28l / Min Viscosity range 1~1,000,000cps Operating air pressure 5kgf/cm² Maximum fluid charge

BV-T520PCapable to continuously work on the two liquid type materials of minimum quantities, with no interference of pot life by discharging the respective primary agent & hardener simultaneously with mixing. (Precision nozzle type) <SPECIFICATIONS> Operating type Needle Off Maximum dose 0.8l/Min Viscosity